Does anyone know the steps to program the remote, my dealer gave me 2
remotes but only one was programmed.
thanks,
Mark
27
Jan
350Z programming remote
Does anyone know the steps to program the remote, my dealer gave me 2
remotes but only one was programmed.
thanks,
Mark
Buckaroo Banzai wrote:
> Does anyone know the steps to program the remote, my dealer gave me 2
> remotes but only one was programmed.
> thanks,
> Mark
Take the remote back and they will program it for you. No, I don’t
remember how it is done. It does not require the use of the Consult II
scan tool so if someone out there knows how it is done they can get you
the instructions. But, the car is new and they should program it for
free. They did on my Maxima…
I know people are always wanting to know how to
program additional remotes for the keyless
entry/alarm
so what follows is the procedure from the Nissan
Service Manual. Enjoy.
For 1998-2000 Maxima, Pathfinder, Sentra, Altima,
and
Frontier Vehicles 2000 Quest and Xterra Vehicles:
1. Programming Procedure:
A. Get in the vehicle. Close and lock all doors
using the
driver’s power door lock-unlock switch.
B. Insert and remove the ignition key more than 6
times within a 10 second period (at a rate of one
insertion/removal cycle per second). The key should
be
withdrawn from the ignition key cylinder completely
each time it is removed.
NOTE : Do not rush the insertion/removal key
cycling
process.
C. Turn the ignition key to the "ACC" position. The
ignition key should remain in the "ACC" position
throughout the remainder of the programming,
including programming of additional remote
controllers.
D. Press any button on the remote controller one
time.
NOTE : Do not press the button more than one time
in
the above step. If the button is pressed more than
one time, the programming procedure will not be
successful.
The hazard warning lights will flash twice when
this
step is accurately completed and programming is
successful. For 2000 Quest vehicles, the side
marker/tail/license lamps will flash twice when
programming is successful.
E. If you are programming only one remote, proceed
to step 3A. If programming additional remotes,
continue with step 2A, below.
2. Programming Additional Remote Controllers
(Maximum of 4 Remotes):
A. Remain inside the vehicle after programming the
first remote.
B. Use the driver’s power door lock-unlock switch
to
unlock and then lock the doors.
C. Press any button on one of the additional remote
controllers one time.
NOTE : Do not press the button more than one time
in
the above step. If the button is pressed more than
one time, the programming procedure will not be
successful.
The hazard warning lights will flash twice when
programming is successful. For 2000 Quest vehicles,
the side marker/tail/license lamps will flash twice
when
programming is successful.
If there is more than one additional remote to be
programmed, repeat steps 2A through 2C above for
each additional remote.
3. End Programming:
A. Remove the key from the ignition.
B. Use the door lock-unlock switch on the driver’s
door
to unlock the doors. Open the driver’s door to
complete the programming
C. Check the operation of each of the remote
controllers by locking/unlocking the doors with
each
remote controller you have programmed.
Thanks, i’ll give it a try. Yeah, i just wanted to know so that i don’t
have to take it back to the dealer each time my battery goes dead. But
yeah, the dealer was supposed to program it, but they said they didn’t know
how at the time and will call when they learn how, so i didn’t get a call
yet (a week now), so i thought i would ask.
thanks again,
Mark
"Corvette" <sudder…@mindspring.com> wrote in message
news:3D754FDE.65B3B557@mindspring.com…
- Hide quoted text — Show quoted text -
> I know people are always wanting to know how to
> program additional remotes for the keyless
> entry/alarm
> so what follows is the procedure from the Nissan
> Service Manual. Enjoy.
> For 1998-2000 Maxima, Pathfinder, Sentra, Altima,
> and
> Frontier Vehicles 2000 Quest and Xterra Vehicles:
> 1. Programming Procedure:
> A. Get in the vehicle. Close and lock all doors
> using the
> driver’s power door lock-unlock switch.
> B. Insert and remove the ignition key more than 6
> times within a 10 second period (at a rate of one
> insertion/removal cycle per second). The key should
> be
> withdrawn from the ignition key cylinder completely
> each time it is removed.
> NOTE : Do not rush the insertion/removal key
> cycling
> process.
> C. Turn the ignition key to the "ACC" position. The
> ignition key should remain in the "ACC" position
> throughout the remainder of the programming,
> including programming of additional remote
> controllers.
> D. Press any button on the remote controller one
> time.
> NOTE : Do not press the button more than one time
> in
> the above step. If the button is pressed more than
> one time, the programming procedure will not be
> successful.
> The hazard warning lights will flash twice when
> this
> step is accurately completed and programming is
> successful. For 2000 Quest vehicles, the side
> marker/tail/license lamps will flash twice when
> programming is successful.
> E. If you are programming only one remote, proceed
> to step 3A. If programming additional remotes,
> continue with step 2A, below.
> 2. Programming Additional Remote Controllers
> (Maximum of 4 Remotes):
> A. Remain inside the vehicle after programming the
> first remote.
> B. Use the driver’s power door lock-unlock switch
> to
> unlock and then lock the doors.
> C. Press any button on one of the additional remote
> controllers one time.
> NOTE : Do not press the button more than one time
> in
> the above step. If the button is pressed more than
> one time, the programming procedure will not be
> successful.
> The hazard warning lights will flash twice when
> programming is successful. For 2000 Quest vehicles,
> the side marker/tail/license lamps will flash twice
> when
> programming is successful.
> If there is more than one additional remote to be
> programmed, repeat steps 2A through 2C above for
> each additional remote.
> 3. End Programming:
> A. Remove the key from the ignition.
> B. Use the door lock-unlock switch on the driver’s
> door
> to unlock the doors. Open the driver’s door to
> complete the programming
> C. Check the operation of each of the remote
> controllers by locking/unlocking the doors with
> each
> remote controller you have programmed.
- Hide quoted text — Show quoted text -
Buckaroo Banzai wrote:
> Thanks, i’ll give it a try. Yeah, i just wanted to know so that i
don’t
> have to take it back to the dealer each time my battery goes dead.
But
> yeah, the dealer was supposed to program it, but they said they
didn’t know
> how at the time and will call when they learn how, so i didn’t get a
call
> yet (a week now), so i thought i would ask.
> thanks again,
> Mark
> "Corvette" <sudder…@mindspring.com> wrote in message
> news:3D754FDE.65B3B557@mindspring.com…
> > I know people are always wanting to know how
to
> > program additional remotes for the keyless
> > entry/alarm
> > so what follows is the procedure from the
Nissan
> > Service Manual. Enjoy.
> > For 1998-2000 Maxima, Pathfinder, Sentra,
Altima,
> > and
> > Frontier Vehicles 2000 Quest and Xterra
Vehicles:
> > 1. Programming Procedure:
> > A. Get in the vehicle. Close and lock all
doors
> > using the
> > driver’s power door lock-unlock switch.
> > B. Insert and remove the ignition key more
than 6
> > times within a 10 second period (at a rate of
one
> > insertion/removal cycle per second). The key
should
> > be
> > withdrawn from the ignition key cylinder
completely
> > each time it is removed.
> > NOTE : Do not rush the insertion/removal key
> > cycling
> > process.
> > C. Turn the ignition key to the "ACC"
position. The
> > ignition key should remain in the "ACC"
position
> > throughout the remainder of the programming,
> > including programming of additional remote
> > controllers.
> > D. Press any button on the remote controller
one
> > time.
> > NOTE : Do not press the button more than one
time
> > in
> > the above step. If the button is pressed more
than
> > one time, the programming procedure will not
be
> > successful.
> > The hazard warning lights will flash twice
when
> > this
> > step is accurately completed and programming
is
> > successful. For 2000 Quest vehicles, the side
> > marker/tail/license lamps will flash twice
when
> > programming is successful.
> > E. If you are programming only one remote,
proceed
> > to step 3A. If programming additional
remotes,
> > continue with step 2A, below.
> > 2. Programming Additional Remote Controllers
> > (Maximum of 4 Remotes):
> > A. Remain inside the vehicle after
programming the
> > first remote.
> > B. Use the driver’s power door lock-unlock
switch
> > to
> > unlock and then lock the doors.
> > C. Press any button on one of the additional
remote
> > controllers one time.
> > NOTE : Do not press the button more than one
time
> > in
> > the above step. If the button is pressed more
than
> > one time, the programming procedure will not
be
> > successful.
> > The hazard warning lights will flash twice
when
> > programming is successful. For 2000 Quest
vehicles,
> > the side marker/tail/license lamps will flash
twice
> > when
> > programming is successful.
> > If there is more than one additional remote
to be
> > programmed, repeat steps 2A through 2C above
for
> > each additional remote.
> > 3. End Programming:
> > A. Remove the key from the ignition.
> > B. Use the door lock-unlock switch on the
driver’s
> > door
> > to unlock the doors. Open the driver’s door
to
> > complete the programming
> > C. Check the operation of each of the remote
> > controllers by locking/unlocking the doors
with
> > each
> > remote controller you have programmed.
FOLOW TO Buckaroo Banzai INSTRUCTIONS, THAT WORKS!!!!!!!
AND THANKS A LOT
RICARDO FLORES SANCHEZ
- Hide quoted text — Show quoted text -
Buckaroo Banzai wrote:
> Thanks, i’ll give it a try. Yeah, i just wanted to know so that i
don’t
> have to take it back to the dealer each time my battery goes dead.
But
> yeah, the dealer was supposed to program it, but they said they
didn’t know
> how at the time and will call when they learn how, so i didn’t get a
call
> yet (a week now), so i thought i would ask.
> thanks again,
> Mark
> "Corvette" <sudder…@mindspring.com> wrote in message
> news:3D754FDE.65B3B557@mindspring.com…
> > I know people are always wanting to know how
to
> > program additional remotes for the keyless
> > entry/alarm
> > so what follows is the procedure from the
Nissan
> > Service Manual. Enjoy.
> > For 1998-2000 Maxima, Pathfinder, Sentra,
Altima,
> > and
> > Frontier Vehicles 2000 Quest and Xterra
Vehicles:
> > 1. Programming Procedure:
> > A. Get in the vehicle. Close and lock all
doors
> > using the
> > driver’s power door lock-unlock switch.
> > B. Insert and remove the ignition key more
than 6
> > times within a 10 second period (at a rate of
one
> > insertion/removal cycle per second). The key
should
> > be
> > withdrawn from the ignition key cylinder
completely
> > each time it is removed.
> > NOTE : Do not rush the insertion/removal key
> > cycling
> > process.
> > C. Turn the ignition key to the "ACC"
position. The
> > ignition key should remain in the "ACC"
position
> > throughout the remainder of the programming,
> > including programming of additional remote
> > controllers.
> > D. Press any button on the remote controller
one
> > time.
> > NOTE : Do not press the button more than one
time
> > in
> > the above step. If the button is pressed more
than
> > one time, the programming procedure will not
be
> > successful.
> > The hazard warning lights will flash twice
when
> > this
> > step is accurately completed and programming
is
> > successful. For 2000 Quest vehicles, the side
> > marker/tail/license lamps will flash twice
when
> > programming is successful.
> > E. If you are programming only one remote,
proceed
> > to step 3A. If programming additional
remotes,
> > continue with step 2A, below.
> > 2. Programming Additional Remote Controllers
> > (Maximum of 4 Remotes):
> > A. Remain inside the vehicle after
programming the
> > first remote.
> > B. Use the driver’s power door lock-unlock
switch
> > to
> > unlock and then lock the doors.
> > C. Press any button on one of the additional
remote
> > controllers one time.
> > NOTE : Do not press the button more than one
time
> > in
> > the above step. If the button is pressed more
than
> > one time, the programming procedure will not
be
> > successful.
> > The hazard warning lights will flash twice
when
> > programming is successful. For 2000 Quest
vehicles,
> > the side marker/tail/license lamps will flash
twice
> > when
> > programming is successful.
> > If there is more than one additional remote
to be
> > programmed, repeat steps 2A through 2C above
for
> > each additional remote.
> > 3. End Programming:
> > A. Remove the key from the ignition.
> > B. Use the door lock-unlock switch on the
driver’s
> > door
> > to unlock the doors. Open the driver’s door
to
> > complete the programming
> > C. Check the operation of each of the remote
> > controllers by locking/unlocking the doors
with
> > each
> > remote controller you have programmed.
Just a quick note to say I had same problem: my garage door is RF, not
Infra Red, I thought "there’s no way to teach an RF code to this gizmo!"
The instruction came with the 350Z ’05 (even a separate card!) were bad-
but I followed them w care- and did not work! So I said to mself "See,
no good for RF!"
But, last whim, I called the 800# from the website
Which, BTW, is here: http://tinyurl.com/4dh4j
the guys there could not have been nicer: it took just 2 minutes to
correct the error in the Nissan card’s instructions, and it works great.
-Pham